2-cycle weed eaters typically use a 40:1 or 50:1 ratio of fuel to oil. 4-cycle weed eaters keep the gas and oil separate, so you can use regular fuel. Never use fuel that contains more than 10% of ethanol, as many small engines aren’t equipped to handle that ingredient. Those are the basics, but there are a couple of other factors you should ...Solution. Two-cycle engines run on a mixture of gasoline and oil. Each engine type is designed to run on a specific gas-to-oil mix ratio. To confirm the correct ratio for your equipment, check your Operator's Manual. IMPORTANT: Use only oil that is labeled for use in “Two-cycle” or “Two-stroke” engines. Two-cycle oil is available at ...Steps for mixing two-stroke fuel and oil. Use a clean, airtight container intended for fuel. Not only will doing so prolong the shelf life of your fuel mix, but it will help prevent permeation and evaporation. Always start by filling the container with half the amount of the gas to be used. Add the entire amount of oil.Basically, it is not too hard to calculate it. The most common fuel/oil mix ratio is 40:1. That means that you need 40 parts of gas to one gallon of oil. The same rule applies to the other two mixtures. If you know that one gallon of oil is equal to 128 oz. (1 US gallon), you just need to divide 128 oz. with the recommended mix ratio and you ...Learn how to correctly mix and store 2 stroke fuel used in RYOBI power garden equipment.A 2-cycle engine in a string trimmer uses gas and oil mixed at a ratio of 50:1, 40:1, or 32:1. For example, 50:1 mix equals 50 parts gasoline to 1 part oil. The mix your string trimmer requires varies by manufacturer. You can find the correct ratio in your operator’s manual. You may also find it located on the fuel cap.Typically, a ratio of 40:1 or 50:1 is recommended for most weed eaters, which means 40 or 50 parts gasoline to one part oil. To measure the oil, use a measuring cup or a pre-mixed fuel can with the correct ratio of oil already added. Pour the oil slowly and carefully, making sure not to overfill the tank.All the units in our best weedeater comparison run on gasoline. Four of the string trimmers are 4-cycle** and require only gasoline—no remixing or oil. The Makita EM2650LH, Ryobi RY4CSS, Honda HHT35SLTA, and the Troy-Bilt TB6044 XP are all 4-cycle. **The STIHL FS 91 R is also a 4-stroke, but it runs on 2-stroke fuel (premix).The new Troy-Bilt ® 4-cycle string trimmer was engineered from the ground up to be easy to start and maintain. And, you still don't have to mix oil and gas with our 4-stroke engine technology. And, you still don't have to mix oil and gas with our 4-stroke engine technology.Prepare a batch of fuel for the GT 200R by first pouring a half-gallon of fresh gasoline into a clean 1-gallon container. Add 2.6 fluid ounces of two-cycle engine oil, close the container and shake until the gasoline and oil are well mixed. Add another half gallon of gasoline to the container, close it, and shake it again to remix the gas and oil.ECHO Consumer Product Support. If you require assistance or have questions concerning the application, operation, or maintenance of this product, call the ECHO Consumer Product Support Department at 1-800-432-ECHO (3246) from 8:00 a.m. to 5:00 p.m. (Central Standard Time) Monday through Friday.Quick video on how to mix gas and 2 cycle engine oil for your small engine outdoor equipment such as weedeaters, string trimmers, chainsaws and more...#DIY #...Put the 2-cycle oil into the gas container. Put the cap back on. The fuel and oil should be gently shaken together to combine them. Put more gas into the Homelite string trimmer. Ethanol Shield 2-cycle oil is what you want to use, according to Homelite. Kawasaki’s 2-cycle hybrid is another viable option.To mix gas for your weed eater, you will need a 2-cycle engine oil and unleaded gasoline. The ratio for mixing the gas can vary depending on the manufacturer’s instructions, but a common ratio is typically 50:1 (50 parts gasoline to 1 part oil).Quick Summary. The gas oil ratio for ECHO trimmers is typically 50:1, which means mixing 2.6 ounces of oil with 1 gallon of gasoline. It is important to follow the manufacturer’s recommendations for the correct ratio to ensure optimal performance and prevent damage to the trimmer’s engine.Step 6: First pour the oil into the gas can. After, add the gasoline at the right mix ratio. Once done, you can close the fuel canister. Do not forget to shake the canister by hand to get them completely mixed. Step 7: Don’t go overboard on how much fuel you mix. Mix only enough gasoline that you will use in your engine in the next three months.A weed eater can either have a two-cycle or a four-cycle engine, but the two-cycle engine is the most common and affordable and uses a gas and oil mixture and operates loudly while the four-cycle engine is heavier but runs quieter with fewer fumes.Feb 17, 2024 · Section 2: Fuel Your Weed Eater (for gas-powered) When it comes to using a gas-powered weed eater, there are a few important steps you need to follow to prepare it for use. The first step is to fuel your weed eater properly. Gas-powered weed eaters require a specific type of fuel mixture, typically a combination of gasoline and oil. How to Mix Gas for a 2-stroke: First your gonna need to know the gas to oil ratio on your 2-cycle engine whether its 32:1 or 50:1. On a standard weed-eater the gas to oil ratio is 50:1. but on a high performance dirt bike it may be 30:1 it all depends on each machine you use.Apr 9, 2024 · 4. Divide 128 by 50 for a perfect 50:1 mixture. If you need 1 part of oil for every 50 parts of gas, then divide the total amount of gasoline by 50.The result is 2.6, meaning that you need 2.6 fl. oz. of oil for a gallon of gas. [4] This also works with other mixtures, like 40:1. ECHO Consumer Product Support. If you require assistance or have questions concerning the application, operation, or maintenance of this product, call the ECHO Consumer Product Support Department at 1-800-432-ECHO (3246) from 8:00 a.m. to 5:00 p.m. (Central Standard Time) Monday through Friday.Only apply the kind of oil recommended by the manufacturer. Using something different may considerably reduce the engine performance. Then, mix the gas and the oil at the proper volume ratio. 40:1 and 50:1 are usually the most common mixing ratios used on weed eaters. Finally, fill the fuel tank with the mix, turn on the engine and get down to ...The US is widening its lead as the world's largest producer of hydrocarbons. For seven straight years, the US has pumped more oil and gas out of the ground than any other country. ...Steps for mixing two-stroke fuel and oil. Use a clean, airtight container intended for fuel. Not only will doing so prolong the shelf life of your fuel mix, but it will help prevent permeation and evaporation. Always start by filling the container with half the amount of the gas to be used. Add the entire amount of oil.Dec 4, 2022 · Only apply the kind of oil recommended by the manufacturer. Using something different may considerably reduce the engine performance. Then, mix the gas and the oil at the proper volume ratio. 40:1 and 50:1 are usually the most common mixing ratios used on weed eaters. Finally, fill the fuel tank with the mix, turn on the engine and get down to ... Watch as Jason Emmons from the ECHO chainsaw carving team demonstrates how to correctly mix fuel and oil. ECHO Outdoor Power Equipment recommends a 50 to 1 m...Your Craftsman 2-cycle string trimmer uses a gas and oil mixture at a ratio of 40:1. This means 40 parts gas is mixed with 1 part oil. Refer to the chart below. When creating this mix, use unleaded gasoline with a minimum octane rating of 89 (mid-grade) and maximum ethanol content of 10%.Sep 9, 2003. Messages. 2,635. Location. Arizona. Apr 2, 2008. #8. When I was putting my Poulan blower out to pasture, it ran wide open for an hour on straight gas until it seized. Was using Mobit MX2T for oil.Consider an example, the two-cycle oil mix ratio for weed eater is 40:1. For optimum performance, never use Husqvarna 4-stroke weed eater oil for two-stroke engines. ... Let’s take Husqvarna 223l weed eater gas oil ratio as an example. If you are using a gasoline engine and expect to use 3 gallons of gas during your outing, divide 3 by 1 to ...And the container must be approved for use with fuels. To mix oil and gas, first, you need to pour engine oil in the canister and then mix the gasoline in it. Before pouring it into the engine, you must give it a good mix by shaking the container. After mixing these two in the container, gently pour them in the engine.How do I mix gas for a Craftsman weed eater? To mix gas for a Craftsman weed eater, you will need to use a 2-cycle engine oil that is specifically recommended by Craftsman. The general ratio for Craftsman weed eaters is 40:1, meaning you should mix 3.2 ounces of oil for every gallon of gasoline. How to mix gas and oil for a 2-cycle Toro string trimmer: Use the chart below to determine how much fuel mix to prepare. Remove the cap from an approved gas can. Add unleaded fuel (minimum 87 octane rating & maximum 10% ethanol content) to a gas can. Using the chart for ounces of oil required, add the 2-cycle oil to the gas can. Replace the cap. The Husqvarna weed eater fuel mix ratio is 1.3 to 1.5 gallons of gas per 1.3 gallons of oil. This means that you’ll want to fill your tank three-quarters of the way with gasoline before adding the oil. However, you can also use a Husqvarna weed eater fuel mix ratio calculator. 2-cycle weed eaters typically use a 40:1 or 50:1 ratio of fuel to oil. 4-cycle weed eaters keep the gas and oil separate, so you can use regular fuel. Never use fuel that contains more than 10% of ethanol, as many small engines aren’t equipped to handle that ingredient. Those are the basics, but there are a couple of other factors you should ... May 9, 2024 · Top 7 Gas String Trimmers – Reviews. 1. Ryobi RY253SS 25 cc 2-cycle straight shaft string trimmer. Our top pick, the RY253SS straight shaft model from Ryobi, is affordable, versatile, easy to use for a gas weed eater, and powerful enough for just about any residential yard work. The machine’s 25 cc, 2-cycle engine features a full crankshaft ... Follow these simple steps to mix fuel for your Husqvarna weed eater: Step 1: Safety First: Before handling any fuels or oils, ensure you are in a well-ventilated area away from open flames or sparks. Step 2: Prepare the Gasoline: Use a clean gasoline container and fill it with the required amount of gasoline.90. 31K views 5 years ago. How to find that gas mixture ratio for a string trimmer and how to mix the oil and gas together correctly. I Kendall Todd show you how to find the correct...130C. Tackle tough lawns on with the Husqvarna 130C. This string trimmer starts quickly and easily, thanks to the digital ignition and Smart Start® technology. Perfect for homeowners who need to trim around obstacles, this curved shaft trimmer features an ergonomic design and handle with LowVib® technology for easier, more comfortable use.Gas prices have jumped to near a new record high in the U.S. as Russia's invasion of Ukraine continues to drive oil prices higher. By clicking "TRY IT", I agree to receive newslett...Feb 27, 2020 · Step 6: First pour the oil into the gas can. After, add the gasoline at the right mix ratio. Once done, you can close the fuel canister. Do not forget to shake the canister by hand to get them completely mixed. Step 7: Don’t go overboard on how much fuel you mix. Mix only enough gasoline that you will use in your engine in the next three months. Oct 6, 2022 · However, generally speaking, weed eater oil will be mixed with the following ratios: 50:1. 40:1. 32:1. This means that, if your engine requires a 50:1 mix, you will need to mix 50 parts fuel to 1 part oil. If you can’t find the information in your user manual or you have misplaced it then the correct ratio is also usually found on a label on ... However, generally speaking, weed eater oil will be mixed with the following ratios: 50:1. 40:1. 32:1. This means that, if your engine requires a 50:1 mix, you will need to mix 50 parts fuel to 1 part oil. If you can’t find the information in your user manual or you have misplaced it then the correct ratio is also usually found on a label on ...Can I safely use 10w30 motor oil in a 2 stroke weed eater engine ... 1) Regular engine oil does not readily mix with gasoline. ... 5) If you want to ...The standard mixture for every weed eater is a 40:1 ratio of gas and oil. That means you have to mix 40 parts of gas with one gallon of oil. Always use fresh gas to avoid any damage to the weed eater. It is best to make the amount of fuel you need. Another fact is that your gas and oil mixture has to be perfect. All STIHL gasoline-powered equipment uses a 50:1 gas and oil mixture. The 50 to 1 mix chart below can help you figure out the correct measurements to use. For high-performance fuel that requires no mixing, choose STIHL MotoMix® premixed fuel. A weed trimmer with a 2 -cycle engine runs on a mixture of gasoline and oil. The instructions say to mix one part of oil to 30 parts of gas. A container is filled with four litres of oil. How many litres of gas should be added to the container to make the proper mix of fuel for the weed trimmer. There should be litres of gas added to the container.how to gas and oil weed wacker. I show how to put gas and oil in weed wacker.2 cycle oil linkhttp://amzn.to/2bF0HNXA string trimmer, also called a weed whacker, is a lawn maintenance tool used for removing weeds in hard-to-reach areas and trimming tall grass. A lawn edger, also known as a lawn trimmer, is used to create the line between where the lawn ends and the sidewalk begins. ... gas weed eater. gas trimmer. bump gas string trimmers. Explore …Jun 21, 2020 · Lawn care, equipment Showing how to mix 2 Stroke Gas Mixture or 2 cycle fuel fast and easy. 50:1 fuel mixture or 40:1 fuel mixture. Gas Mixture for weed eat... The Husqvarna Weed Eater Fuel mix ratio is 50:1. This means if you’re using Husqvarna Weed Eater, you should use 50 parts of oil (petrol or diesel) and one part of gasoline (unleaded). This is the optimum level of the fuel mixture that’ll help you to achieve maximum output. However, the ratio actually depends on the type of engine used in ...Weed Eater Brand. All Weed Eater brand two-cycle gas trimmers use a 40:1 ratio of gas to oil. That's equal to 3.2 ounces of oil to 1 gallon of regular gas. The gas should be 87 octane with no more than 10 percent alcohol. The oil must be formulated for two-cycle engines.Basically, it is not too hard to calculate it. The most common fuel/oil mix ratio is 40:1. That means that you need 40 parts of gas to one gallon of oil. The same rule applies to the other two mixtures. If you know that one gallon of oil is equal to 128 oz. (1 US gallon), you just need to divide 128 oz. with the recommended mix ratio and you ...The US is widening its lead as the world's largest producer of hydrocarbons. For seven straight years, the US has pumped more oil and gas out of the ground than any other country. ...Advertisement Even the most basic perfumes should blend three scents, or "notes." The combination of a base note, middle note and top note (added in that order) is what causes a pe...Jun 21, 2020 · Lawn care, equipment Showing how to mix 2 Stroke Gas Mixture or 2 cycle fuel fast and easy. 50:1 fuel mixture or 40:1 fuel mixture. Gas Mixture for weed eat... If there is one hill I will die on, it is that boxed mix brownies are usually the only brownies worth my time—but that doesn’t mean I don’t like to get fancy with them. If you’re l...Gas prices are rising after OPEC+ announced cuts to its oil supply, and drivers can expect prices at the pump to increase more this spring. By clicking "TRY IT", I agree to receive...Add a 2-cycle premium oil that is ISO-L-EGD and JASO M345 FD certified like Craftsman full synthetic 2-cycle engine oil. How to mix gas and oil for a 2-cycle string trimmer: Use …A string trimmer, also called a weed whacker, is a lawn maintenance tool used for removing weeds in hard-to-reach areas and trimming tall grass. A lawn edger, also known as a lawn trimmer, is used to create the line between where the lawn ends and the sidewalk begins. ... gas weed eater. gas trimmer. bump gas string trimmers. Explore …Solution. Two-cycle engines run on a mixture of gasoline and oil. Each engine type is designed to run on a specific gas-to-oil mix ratio. To confirm the correct ratio for your equipment, check your Operator's Manual. IMPORTANT: Use only oil that is labeled for use in “Two-cycle” or “Two-stroke” engines. Two-cycle oil is available at ...6 Mar 2020 ... Comments112 · Fixing A Craftsman Trimmer That Someone Gave Up On. · Correct Way To Mix Gas and Oil For a ChainSaw, WeedEater etc. · The BEST&nbs...The fuel-oil mixture ratio for all Weed Eater products is 40:1. You can obtain this ratio by mixing 3.2 oz. of two cycle air cooled engine oil with one gallon of regular gas. Over a period of time oil will separate from gasoline. To properly insure oil and gas mixture, we recommend thoroughly shaking your oil and gas mixture before refueling ... About This Product. TruFuel is the first-ever premixed, ready-to-use fuel engineered specifically for portable 2-cycle gas powered equipment. It provides time-saving convenience and superior performance. Advanced formula and fuel stabilizers precisely blended with full synthetic oil keeps fuel fresh for 2 plus years after opening and 5 plus ... Follow these simple steps to mix fuel for your Husqvarna weed eater: Step 1: Safety First: Before handling any fuels or oils, ensure you are in a well-ventilated area away from open flames or sparks. Step 2: Prepare the Gasoline: Use a clean gasoline container and fill it with the required amount of gasoline.The Husqvarna Weed Eater Fuel mix ratio is 50:1. This means if you’re using Husqvarna Weed Eater, you should use 50 parts of oil (petrol or diesel) and one part of gasoline (unleaded). This is the optimum level of the fuel mixture that’ll help you to achieve maximum output. However, the ratio actually depends on the type of engine used in ...To make fuel for the FS55R string trimmer, mix 2.6 U.S. fluid ounces of high-quality, two-cycle, air-cooled engine oil in 1 U.S. gallon of midgrade unleaded gasoline. Shake well before fueling. The gas should have an octane rating of at least 89, with not more than 10 percent ethanol. Advertisement.For a Mercury two-stroke model, 2- to 20-horsepower outboard motor manufactured before 1980, use a blend of unleaded gasoline with a posted octane minimum of 91 and Mercury or Quic...Mix it up. Use a specifically marked fuel container to blend the oil and gasoline. Do not try to mix them directly in the trimmer's tank. To get the 40-to-1 ratio, add a 3.2-fluid-ounce bottle of the recommended oil to 1 gallon of gasoline. For a larger quantity, add an 8-fluid-ounce bottle of oil to 2.5 gallons of gasoline.When it comes to using a weed eater, it’s essential to mix the gas and oil correctly. The proper mix will ensure your weed eater runs efficiently, reducing the risk of damaging the engine, and extending its lifespan. The common mix is 50:1, which involves mixing two-stroke oil with gasoline.The correct ratio of gas-to-oil mixture for Weed Eater line trimmers is 1 part oil to 40 parts gasoline. The best method of mixing is to start by adding 1 gallon of regular unleaded gasoline to a gas can. Then pour in a 3.2-ounce bottle of good quality, synthetic 2-cycle air-cooled engine oil. Either cap the gas can or turn the nozzle inward ...A weed trimmer with a 2 -cycle engine runs on a mixture of gasoline and oil. The instructions say to mix one part of oil to 30 parts of gas. A container is filled with four litres of oil. How many litres of gas should be added to the container to make the proper mix of fuel for the weed trimmer. There should be litres of gas added to the container.Adding oil to gasoline. Pour 1 liter of gasoline into a container of suitable volume and add 1/2 of the required amount of oil. Stir gently while keeping a good distance from open flames. Add the remaining half of the oil …China's bullying of Vietnam prompted a blunt US response this week. Tensions surrounding the South China Sea have always been largely about oil and natural gas. But it’s often been...Use a 32:1 gasoline to oil ratio. One gallon of gasoline combined with 4 oz of two-cycle engine oil. If you are in the state of California, use a 2-cycle oil mix ratio of 40:1. For two-cycle handheld equipment manufactured after 2002: Use a 40:1 two-cycle oil mix ratio. One gallon of gasoline combined with 3.2 oz of two-cycle engine oil.To mix gas for your Murray weed eater, you should use a 50:1 ratio of gas to oil. This means you should mix 2.6 ounces of 2-cycle engine oil with 1 gallon of gasoline. Make sure to mix the gas and oil thoroughly before filling up your weed eater’s fuel tank.To mix the gas and oil, you’ll need a clean, empty gas can with measuring marks. Start by pouring the correct amount of oil into the can, making sure to use a funnel to avoid spills. Then, add the gasoline up to the appropriate mark, and give it a good shake to ensure everything is well mixed.Watch on. The 50:1 fuel mix ratio for Echo weed eaters is calculated as follows: 50 parts gasoline to 1 part of two-stroke engine oil. To mix the fuel and oil, you’ll need a clean gasoline container and a measuring cup specifically designed for measuring small quantities of liquids in fl. oz. Then do the calculations as per the guidelines.Weed Eater writers suggest a 40:1 blend, which translates to 3.2 ounces of oil per 1 gallon of gasoline. Only mix up the amount of fuel/oil blend you plan to use in your current weeding session, as it doesn't age well and can separate.For two-cycle handheld engines produced after 2003: Use a 40-to-1 ratio (to aid in the reduction of emissions). This can be made by mixing 3.2 ounces of two-cycle engine oil with 1 gallon of gasoline. If you are unsure of the year your equipment was made: Use the 40:1 mixture. All of our handheld two-cycle units can operate on a 40:1 mixture.Husqvarna gas string trimmers are packed with smart features to optimise the user experience. Our wide range of string trimmers includes battery- and electric string trimmers and combi trimmers. Show more. Husqvarna's gas weed eaters provide unmatched precision and power. Achieve a neat and professional finish with our top-rated string trimmers.16 Aug 2014 ... Learn how you can mix the petrol and oil for the whipper snipper or weed whacker. Different machine will require different mix ratio, ...2-cycle weed eaters typically use a 40:1 or 50:1 ratio of fuel to oil. 4-cycle weed eaters keep the gas and oil separate, so you can use regular fuel. Never use fuel that contains more than 10% of ethanol, as many small engines aren’t equipped to handle that ingredient. Those are the basics, but there are a couple of other factors you should ... How to mix gas and oil for a 2-cycle Toro string trimmer: Use the chart below to determine how much fuel mix to prepare. Remove the cap from an approved gas can. Add unleaded fuel (minimum 87 octane rating & maximum 10% ethanol content) to a gas can. Using the chart for ounces of oil required, add the 2-cycle oil to the gas can. Replace the cap. 8 Dec 2007 ... Newer ones do well with 50:1 mixtures. But, still, I would check with the manufacturer to be sure. Small engines can be finicky. My Stihl heavy- ...All STIHL gasoline-powered equipment uses a 50:1 gas and oil mixture. The 50 to 1 mix chart below can help you figure out the correct measurements to use. For high …Measuring the 40:1 fuel mixture for a Bolens weed eater is simple: With one gallon of fresh gasoline, add 3.2 ounces of oil. Alternatively, if using one liter of gasoline, mix in 25 ml of oil. For a 50:1 fuel mixture ratio, combine one gallon of gasoline with 2.6 ounces of oil or 20 ml of oil for one liter of gasoline.
For two-cycle handheld engines produced after 2003: Use a 40-to-1 ratio (to aid in the reduction of emissions). This can be made by mixing 3.2 ounces of two-cycle engine oil with 1 gallon of gasoline. If you are unsure of the year your equipment was made: Use the 40:1 mixture. All of our handheld two-cycle units can operate on a 40:1 mixture.. 9dpo no symptoms
To mix gas for your Stihl weed eater, you will need to combine the correct ratio of fuel and oil. Stihl recommends a 50:1 ratio, which is 2.6 ounces of oil per gallon of gasoline. Mix the gas and oil in an approved fuel container and shake well to ensure thorough mixing.Weed Eater Brand. All Weed Eater brand two-cycle gas trimmers use a 40:1 ratio of gas to oil. That's equal to 3.2 ounces of oil to 1 gallon of regular gas. The gas should be 87 octane with no more than 10 percent alcohol. The oil must be formulated for two-cycle engines.be mounted on it. The term "trimmer" is used to designate an FS unit that is equipped with a nylon line head or a head with flexible plastic blades (i.e., the PolyCut head.) FS models with an "R" on the nameplate were originally configured (at the time of distribution) as a trimmer with a loop handle. Have your STIHL dealer show you how Use a 32:1 gasoline to oil ratio. One gallon of gasoline combined with 4 oz of two-cycle engine oil. If you are in the state of California, use a 2-cycle oil mix ratio of 40:1. For two-cycle handheld equipment manufactured after 2002: Use a 40:1 two-cycle oil mix ratio. One gallon of gasoline combined with 3.2 oz of two-cycle engine oil. If you earned money with an oil well, you may want to know how to calculate your net revenue interest for your tax return. It's relatively easy to do so in a few simple steps. To c...A new global forecast illustrates the old law of supply and demand. By clicking "TRY IT", I agree to receive newsletters and promotions from Money and its partners. I agree to Mone...how to mix up 2 stroke gas for leaf blowers, saws, weedeaters/weedwhackers anything with a 2 stroke (two cycle) engine on it. be sure to use ratio that the m...12 Apr 2005 ... I have a stihl weed eater and use the 50:1 bottles of 2 cycle mix. Can I use the 50:1 oil in the chainsaw? I searched this site and found some ...For example, if your fuel/oil mix ratio is 40:1, this means you need 40 part gasoline to 1 part oil. One gallon of oil is equal to 128 oz., so for a 40:1 ratio, you would divide 128 oz. by the mix ratio of 40 and see that you need 3.2 ounces of oil: 128/40 = 3.2 oz. of oil.1. Best Overall Pick: Husqvarna 128LD Gas String Trimmer. View on Amazon. Why we like it: The Husqvarna 128LD Gas String Trimmer is rugged, lightweight, and one of the most versatile trimmers on the market today. Editor’s Rating: Quick Facts. Power: 28cc. Cut radius: 17 inches. Weight: 10.8 pounds.Apr 19, 2015 · 4. 40:1 would b3 3.2oz of oil per gallon of gas. Was this answer helpful? Michael posted an answer 5 years, 11 months ago. 0 4 OUNCES PER GALLON IS NOT 40:1. Please remove Michelle's answer. Her ratio info is incorrect. That mixture would be 32:1. More rich in oil, than a 40:1 mixture. Maybe you're mixing your gas and oil wrong. Let me teach you the proper way to mix gas and ... Are you tired of clogged carburetors or engines that won't start? Maybe you're mixing your gas and ...2.4K subscribers. Subscribed. 195. 18K views 3 years ago. Lawn care, equipment Showing how to mix 2 Stroke Gas Mixture or 2 cycle fuel fast and easy. 50:1 …16 Aug 2014 ... Learn how you can mix the petrol and oil for the whipper snipper or weed whacker. Different machine will require different mix ratio, ...Mixing the gas and oil in proportion is one way to get the best from your weed eater. The most common ratio of gas to oil mixture is 50:1 and 40:1, depending on the product. It might seem a little tricky to calculate. However, it’s something other than basic math. How To Mix Gas And Oil For Weed eater (Easy Guide)Lawn care, equipment Showing how to mix 2 Stroke Gas Mixture or 2 cycle fuel fast and easy. 50:1 fuel mixture or 40:1 fuel mixture. Gas Mixture for weed eat...8. Husqvarna 128DJX. The Husqvarna 128DJx is a powerful brushcutter that’s lightweight and easy to use. Even though this model is best suited for small to medium-sized yards, the gas-powered model features a 1.1 horsepower, 28cc engine that’s powerful enough to cut through even the most unruly of weeds.Mix it up. Use a specifically marked fuel container to blend the oil and gasoline. Do not try to mix them directly in the trimmer's tank. To get the 40-to-1 ratio, add a 3.2-fluid-ounce bottle of the recommended oil to 1 gallon of gasoline. For a larger quantity, add an 8-fluid-ounce bottle of oil to 2.5 gallons of gasoline.Wrong Fuel Mix. Typically a weed eater will have a 50:1 fuel-to-oil mixture. If you don’t get your weed eater fuel mixture right, then fuel combustion won’t happen as intended, resulting in a series of different problems. Having too much oil in your mix leads to symptoms such as additional smoke, poor performance, and excessive carbon deposits.Old fuel clogging the engine. Not enough fuel to power the weed eater. Wrong fuel mix ratio prevents the engine from starting. Solution. Open the tank and check how much fuel is in it. If the tank is almost empty, you need to add more fuel. But first give it a swish to make sure the fuel has not turned gummy..